|
|
|
|
Gases Measured |
 |
Oxygen (O2)
|
|
Method of Detection |
|
Electrochemical sensor, paramagnetic sensor or zirconia sensor (depending on desired accuracy and sample composition)
|
|
Ranges Available |
|
0-5 to 0-25% O2
|
|
Resolution |
|
0.1% on % ranges, 1 PPM on PPM ranges
|
|
Accuracy & Repeatability |
|
± 1-2% of full scale
|
|
Drift |
|
Less than 2% of full scale per month
|
|
Response Time (T-90) |
|
20-30 seconds to 90% of step change
|
|
Ambient Temperature Range |
|
32 to 122°F (0 to 50°C) @ 5-95% RH non-condensing. Lower temperatures (-5°F, -20°C) with Cold Weather Package. Sample dew point should be at least 9°F (5°C) below lowest sample temperature.
|
|
Linearity |
|
±1% of full scale
|
|
Size & Weight |
|
Dimensions and weight will vary with configurations selected
|
|
Power |
|
115 VAC, 60 Hz
220 VAC, 50 Hz
|
|
Alarms |
|
High or low alarm contacts available for all gases and low flow
|
|
Code Numbers for Gases Measured |
|
O2 by electrochemical sensor, paramagnetic sensor or zirconia sensor (depending on desired accuracy and sample composition)
|
|
Sampling System |
|
Std SS probe with unheated pre-filter (Std. probe 3/8" O.D. x 18") (9.5 x 460 mm)
|
|
Display Type |
|
D1 - LED display (s) - Manual potentiometer calibration
D2 - LED display (s) - Manual push-button calibration
D3 - Microprocessor controller with single graphic display. Allows auto sequencing, RS-485 output, 'CAL NOW' and one-step
D4 - Same as D3 but with full auto-calibration
|
|
Output Options |
|
OP1 - 4-20 mA non-isolated
OP2 - 4-20 mA isolated
OP3 - 0-5 V
OP4 - 0-10 V
OP5 - RS-485
OP6 - Modbus
|
|
Analyzer Type |
|
Flue Gas Analyzer
|
|
Industry Type |
|
Flue Gas or Emissions
|
|
| |
|
Continuous analysis of flue gas for any combination and range of O2, CO, CO2, SO2, NOx (NO or NO + NO2) or combustibles from combustion processes.
| |
|
- Best value continuous flue gas analyzer with modular sample conditioning
- Oxygen detected by either long life electrochemical sensor, high accuracy paramagnetic sensor or zirconia sensor, depending on desired accuracy and sample composition
- Fast response time and bright digital readout
- Microprocessor based with push button calibration
- Easy to maintain modular layout
- Sample preparation includes moisture removal.
| |
|
- Hi/Low gas, low flow, and diagnostic alarms available
- Isolated analog, RS232, RS485, MODBUS, and Ethernet outputs available
- Cabinet purge system available for use in hazardous areas
- One-step 'cal-now' button with touch screen LCD display
- Full automatic calibration with touch screen LCD display and low flow switch
- Cold weather package for operation to -5°F (-20°C)
- Cabinet coolers can be fitted to most models
- Sensors mounted in heated box for reduced drift
- High temperature filters and probes
Optional sample conditioning includes:
- Continuous water pre wash system for acidic fuel gases present but not to be analyzed (Model 7300)
- Nafion-Tube™ based sample dryer for high accuracy analysis of acidic samples, where NO2 or SO2 are to be measured (Model 7250)
- Heated stack filter for removal of dust from high dust load (> µ) samples (Model 7240)
- Calibration gas injected at heated stack filter to minimize discrepancies due to absorption of soluble gases.
- Multiple sample point sequencer which allows multiple samples to be selected and analyzed (Model 402AS)
| |
|
|
|
|
